Pneumatic Hoist — Winches, Hoists, Cranes, and Derricks

DEPT OF DEFENSE · DEPT OF THE ARMY · AMC · ACC · MISSION & INSTALLATION CONTRACTING COMMAND · 419TH CSB · W6QM MICC-FT DRUM is soliciting Pneumatic Hoist — Winches, Hoists, Cranes, and Derricks. Solicitation number W911S227U0135. Classified under NAICS 333923 — Overhead Traveling Crane, Hoist, and Monorail System Manufacturing. Product/service code 3950 — WINCHES, HOISTS, CRANES, AND DERRICKS. Responses are due by 13 November 2026 20:00 UTC. Posted on SAM.gov, the US federal contract opportunities system; registration is required to bid.

Salient CharacteristicsItem: Pneumatic Chain Hoist Assembly, Lug-Mounted.Brand Name or Equal To. Cisco-Eagle SKU TCRP-1627048 reference model TCRP2000P2.Quantity 2 eaches.1. Required Function. The contractor shall furnish one new, complete, commercially available pneumatically chain hoist assembly for lifting and vertically positioning loads in an overhead lifting application. The offered item shall be fully functional upon delivery and include all components identified below that are necessary for normal operation.2. Mandatory Salient Characteristics. The offered hoist assembly shall meet all of the following minimum requirements:CHARACTERISTIC. MINIMUN GOVERNMENT REQUIREMENTType. Pneumatically powered chain hoist assembly.Rated lifting capacity. Minimum rated capacity of 2 short tons i.e. 4,000 lb.Lift height. Minimum 10 foot vertical lift.Mounting configuration. Lug mounted configuration.Bottom hook. Furnished with a standard bottom hook suitable for the offered hoist���s rated capacity.Pendant control. Furnished with a pendant control. Pendant length shall be 7.5 feet, measured from the hoist, control connection point to the pendant control, or equivalent length necessary to provide the same operating reach.Chain container. Furnished with a canvas chain container sized to safely contain the full length of load chain associated with the required 10 foot lift.Structural, track interface. The assembly shall be compatible with the Government���s existing flange, track interface identified as a 4 inch flange configuration with an applicable flange range of 3.23 inches through 6.02 inches. The vendor shall identify the specific mounting/trolley/interface dimensions of the offered item and certify compatibility with this requirement.Condition. New. Current-production equipment; used, refurbished, remanufactured, or demonstrator equipment is not acceptable.Completeness. Furnished as a complete operational assembly, including the hoist, required mounting/interface components, bottom hook, pendant control, and chain container.Documentation. Furnish manufacturer product literature, dimensional information, installation instructions, operating instructions, maintenance information, rated-capacity information, and warranty documentation.Identification Hoist shall bear permanent manufacturer identification and rated-capacity marking.The reference item identifies the item as a TCRP2000P2 hoist with a 2-ton capacity, 10-foot lift, lug mounted, standard bottom hook, 4 inch Flange 3.23-6.02 inch Flange Range, canvas chain container, and Standard-to-Lift Pendant Length - L = 7.5 ft.3. Offeror Submission RequirementsTo be considered technically acceptable, the vendor shall provide the following with its quotation.Manufacturer name and exact manufacturer part number for the item offered.Manufacturer descriptive literature, specification sheet, and dimensional drawing sufficient to verify:Rated capacity.Lift height.Lug-mount configuration.Bottom-hook configuration.Pendant length.Chain-container material and capacity andCompatibility with the stated 3.23-6.02-inch flange, interface range.If proposing an equal product, clear identification that the product is an equal product, rather than the referenced item.Warranty terms and the name and address of the warranty service point of contact.Proposed delivery lead time and shipping terms.Offerors proposing an equal product shall identify the offered make, model and provide descriptive literature or other adequate descriptive data showing that the item meets the solicitation���s salient characteristics.4. Technical Acceptability Language. Technical acceptability will be evaluated on a pass/fail basis. The quotation will be considered technically acceptable only if the offeror provides sufficient documentation demonstrating that the offered item meets every mandatory salient characteristic. Failure to provide adequate supporting documentation may render the quotation unacceptable.5. Delivery and Acceptance Language. Delivery shall be F.O.B. Destination to the delivery location identified in the solicitation. The Government will inspect the item upon delivery for quantity, visible shipping damage, completeness, manufacturer identification, rated-capacity marking, and compliance with the quoted make and model and required salient characteristics. Acceptance is contingent upon satisfactory inspection and verification of required documentation.