FreeTender
Accepting bidsrfpSouth Africa

RFP 192/2026: Appointment of Contractor to Supply and Install Abattoir Equipment and Supply Facility Furniture at the Lehurutshe Bird and Trophy Hunting Facility under National Department of Tourism (NDT) Programme Tender Volumes , BOQ Compulsory Briefing Session: 25 November 2026 at 11H00 via Microsoft Teams

Issued by Development Bank of Southern Africa · via Development Bank of Southern Africa — Open RFPs

Published
17 Nov 2026
Closes
8 Dec 2026, 23:59 UTC
Reference
RFP 192/2026: Compulsory Briefing Session
Location
South Africa
Sector
Manufacturing & Supply

At a glance

Development Bank of Southern Africa in South Africa has published a request for proposals in manufacturing & supply: “RFP 192/2026: Appointment of Contractor to Supply and Install Abattoir Equipment and Supply Facility Furniture at the Lehurutshe Bird and Trophy Hunting Facility under National Department of Tourism (NDT) Programme Tender Volumes , BOQ Compulsory Briefing Session: 25 November 2026 at 11H00 via Microsoft Teams”. Submissions close on 8 December 2026, 22 days from today. Quote reference RFP 192/2026: Compulsory Briefing Session in any correspondence with the buyer. 2 documents are attached to this notice. FreeTender has recorded 136 notices from this buyer since 2026, 37 of them currently open. There are 97 open manufacturing & supply notices in South Africa on FreeTender. Bids are submitted to the buyer through Development Bank of Southern Africa — Open RFPs, not through FreeTender.

Details

RFP 192/2026: Compulsory Briefing Session: RFP 192/2026: Appointment of Contractor to Supply and Install Abattoir Equipment and Supply Facility Furniture at the Lehurutshe Bird and Trophy Hunting Facility under National Department of Tourism (NDT) Programme Tender Volumes , BOQ Compulsory Briefing Session: 25 November 2026 at 11H00 via Microsoft Teams

LEHERUTSHE ABATTOIR ALTERATION AND EQUIPPING

SECTION NO. 1 PRELIMINARIES

Amount

SUMMARY OF CATEGORIES Category: Fixed R........................... Category : Value R........................... Category : Time R........................….. 1 Prov Sum

Section No. 1 Carried to Final Summary RBill No. 1 Preliminaries 2

SECTION NO. 2 DEMOLITIONS

Unit Quantity Rate Amount DEMOLITIONS

SECTION NO. 2 DEMOLITIONS BILL NO. 1

Explosives No explosives whatsoever may be used for demolition purposes unless otherwise stated General Unless otherwise described all materials are to become the property of the contractor and are to be removed from the site DEMOLITIONS Breaking up and removing 100mm Thick reinforced concrete surface beds, paving, etc 1 m² 1Demolishing and removing Half brick walls 2.8m high 2 m 6SUPPLEMENTARY PREAMBLES

Section No. 2 Carried to Final Summary RBill No. 1 Demolitions 4

SECTION NO. 3 NEW WORKS

EARTHWORKS

SECTION NO. 3 NEW WORKS BILL NO. 1

EXCAVATIONS ETC Open face excavation in earth Open face excavation 1 m³ 5Extra over all excavations for carting away Surplus material from excavations and stock piles on site to a dumping site to be located by the contractor 2 m³ 5Risk of collapse of excavations Sides of bulk excavations not exceeding 1,5m deep 3 m² 7Keeping excavations free of water Keeping excavations free of water other than subterranean water 4 Item

Section No. 3 Carried To Section Summary RBill No. 1 Earthworks 6

CONCRETE, FORMWORK AND REINFORCEMENT

SECTION NO. 3 NEW WORKS BILL NO. 2

UNREINFORCED CONCRETE CAST AGAINST EXCAVATED SURFACES 20Mpa/19mm concrete Sub slab 1 m³ 2Wearing slab over insulation 2 m³ 1CONCRETE SUNDRIES Finishing top surfaces of concrete smooth with a power float Surface beds, slabs, etc 3 m² 7REINFORCEMENT (CPAP WORK GROUP NO. 114) Fabric reinforcement Type 193 fabric reinforcement in concrete surface beds etc 4 m² 14 Section No. 3 Carried To Section Summary RBill No. 2 Concrete, Formwork And Reinforcement 7 WATERPROOFING

SECTION NO. 3 NEW WORKS BILL NO. 3

DAMPPROOFING OF WALLS AND FLOORS Isoboard 25mm Isoboard In floors 1 m² 72 layers of 75mm Isoboard In floors 2 m² 14 25mm hyperelastic damp proofing sheet in floor 3 m² 7150mm hyperelastic damp proofing sheet in walls 4 m² 330mm silica sand bed 5 m² 7Soft board to joint 6 m² 7Aluminium radius coving with concealed fixing bracket, rivets @ 40mm centre to centre to panel skins, sealants to be white silicone and mastic 7 m 22

Section No. 3 Carried To Section Summary RBill No. 3 Waterproofing 8

CARPENTRY AND JOINERY

SECTION NO. 3 NEW WORKS BILL NO. 4

CARPENTRY AND JOINERY Fixing Items described as nailed shall be deemed to be fixed with hardened steel nails or pins, or to be shot-pinned, to brickwork or concrete Items described as plugged shall be deemed to include screwing to fibre, plastic or metal plugs at not exceeding 500mm centres, and where described as bolted, the bolts have been given elsewhere …

Context for bidders

We hold 136 notices from Development Bank of Southern Africa, going back to July 2026 — 37 of them still open. They buy mostly in Construction & Infrastructure, Financial & Professional Services and Water & Environment. There are 97 open Manufacturing & Supply tenders in South Africa. This one closes in 22 days.

More from this buyer

Explore South Africa

Documents

  • RFP192.2026 Tender Volumes.zipDownload
  • RFP192.2026_Abattoir BOQ Bills OF Quantities-Unpriced.pdfDownload

Before you bid on this tender

A quick checklist to help you decide whether to bid and prepare a compliant submission for this manufacturing & supply opportunity. Always verify the details on the official source.

  • Confirm the exact closing date and time (and time zone) on the official portal — deadlines are strict and can be revised by a corrigendum.
  • Read the full notice and every attached document, including the scope, specifications and any bill of quantities or terms of reference.
  • Check the eligibility criteria — prior similar experience, annual turnover, certifications and registrations — and make sure you qualify before investing effort.
  • Prepare any earnest-money deposit (EMD) or bid security and the required formats early; missing or wrongly-formatted documents are a common cause of rejection.
  • Note how bids must be submitted (online or physical), in what format, and whether a digital signature or portal registration is required.
  • Watch for corrigenda and clarifications right up to the deadline — requirements and dates can change.

More Manufacturing & Supply tenders

All Manufacturing & Supply tenders →

FreeTender mirrors this notice for reference. Verify the details and bid on the official portal.

Verify & apply on the official portal →